进口高压泵,进口高压泵厂家,意大利进口高压泵
1、动力端
(1)在运转前必须检查、控制油位。在泵**次运转30小时后须更换润滑油。以后每工作200小时换油一次。
(2)全部螺丝必须拧紧。
(3)泵在运转过程中,润滑油温度不大于70℃,介质温度不得大于55℃。
(4)换油只应在油仍然热的时候进行,旧油要完全放净。曲轴箱内发现铁屑,应用磁铁吸净,堵住油塞,再从注油孔将油注入。油过多会因油中阻力太大而增加油温。
(5)每年至少有一次将油放空,用冲洗油冲洗曲轴箱,然后注入新油。
(6)每次换油之前,应先检查哪些地方水可能进入曲轴箱或漏油,并检查所有密封件和螺丝,特别是中间杆的密封件和柱塞填料,必要时更新。
2、液力端
(1)要将吸入与排出侧的螺丝拧紧。
(2)经常清洗吸入端的过滤器。
(3)吸入与排出阀的漏损会减少往复泵的排量,
在停工时间较长时,应进行调节,检查阀
座、阀座上的“O”型密封圈、阀芯、弹簧
是否磨损,必要时更换。
(4)泵头螺栓装卸按右图所示序号进行。
(5)更换阀座、阀芯要涂以二硫化钼锂基润滑脂。
3、填料函
(1)用**工具拧动锁紧螺母,检查柱塞与中间杆的连接是否紧密,千万注意紧密。
(2)泄露的密封件应更新。
(3)备用的柱塞应涂上防锈油,并保护运动表面和螺纹不受损伤。
换油标准:Mobil(美孚)1130发动机机油
Mobil(美孚)黑霸王柴油机油(SAE15W40)
Shell Helix(壳牌) 施倍力ASX多级油
Shell Helix(壳牌) 劲霸X柴油机机油(SAE15W40)
Shell Helix(壳牌)劲霸C
Castro(嘉德士)金德乐(SAE15W40)
Type Flow rate Max Pressure Speed Max Power Tem
XLT3020ISL 30lpm 7.9gpm 200bar 2900psi 1000rpm 15.6hp 11.5kw 65°C
XLT3020ISR 30lpm 7.9gpm 200bar 2900psi 1000rpm 15.6hp 11.5kw 65°C
XLT1530IR 15lpm 4gpm 300bar 4350psi 1450rpm 11.8hp 8.8kw 65°C
XLT1530IL 15lpm 4gpm 300bar 4350psi 1450rpm 11.8hp 8.8kw 65°C
XLT1830IL 18lpm 4.8gpm 300bar 4350psi 1450rpm 13.7hp 10.1kw 65°C
XLT1830IR 18lpm 4.8gpm 300bar 4350psi 1450rpm 13.7hp 10.1kw 65°C
XLT2230IL 22lpm 5.8gpm 300bar 4350psi 1450rpm 16.6hp 12.2kw 65°C
XLT2230IR 22lpm 5.8gpm 300bar 4350psi 1450rpm 16.6hp 12.2kw 65°C
XLT2530IL 25lpm 6.6gpm 300bar 4350psi 1450rpm 19.2hp 14.1kw 65°C
XLT2530IR 25lpm 6.6gpm 300bar 4350psi 1450rpm 19.2hp 14.1kw 65°C
XLT2730IL 27lpm 7.1gpm 300bar 4350psi 1450rpm 20.5hp 15.1kw 65°C
XLT2730IR 27lpm 7.1gpm 300bar 4350psi 1450rpm 20.5hp 15.1kw 65°C
XLT3025IL 30lpm 7.9gpm 250bar 3625psi 1450rpm 19.3hp 14.2kw 65°C
XLT3025IR 30lpm 7.9gpm 250bar 3625psi 1450rpm 19.3hp 14.2kw 65°C
XLT3325IL 33lpm 8.7gpm 250bar 3625psi 1450rpm 21.4hp 15.7kw 65°C
XLT3325IR 33lpm 8.7gpm 250bar 3625psi 1450pm 21.4hp 15.7kw 65°C
XLT3517IL 35lpm 9.2gpm 170bar 2465psi 1450rpm 15.2hp 11.2kw 65°C
XLT3517IR 35lpm 9.2gpm 170bar 2465pi 1450rpm 15.2hp 11.2kw 65°C
XLT4017IL 40lpm 10.6gpm 170bar 2465psi 1450rpm 17hp 12.5kw 65°C
XLT4017IR 40lpm 10.6gpm 170bar 2465psi 1450rpm 17hp 12.5kw 65°C
XLT4317IL 43lpm 11.4gpm 170bar 2465psi 1450rpm 19.1hp 14.1kw 65°C
XLT4317IR 43lpm 11.4gpm 170bar 2465psi 1450rpm 19.1hp 14.1kw 65°C
XLT5015IL 50lpm 13.2gpm 150bar 2175psi 1450rpm 22.6hp 16.6kw 65°C
XLT5015IR 50lpm 13.2gpm 150bar 2175psi 1450rpm 18.8hp 13.8kw 65°C
XLT5415IL 54lpm 14.3gpm 150bar 2175psi 1450rpm 21.2hp 15.6kw 65°C
XLT5415IR 54lpm 14.3gpm 150bar 2175psi 1450rpm 21.2hp 15.6kw 65°C
XLTI Series
There are two types of XLTI pumps: the first type can operate at a maximum pressure of 300 bar and with water temperatures up to 65°C (149F). This category is particularly suited for fitting on professional high-pressure washers or on small goods vehicles that have to do very challenging cleaning jobs, exploiting its superior performance in terms of pressure. The second type can operate at a maximum pressure of 170 bar, with flow rates up to 54 lpm, and water temperatures up to 65°C (149F). This category offers a superior performance in terms of flow rate and is suitable for fitting on automatic gantry-style car washes, on small goods vehicles for municipal cleaning services, or misting systems or fire extinguishing systems.